top of page
Medex EU Authorised Representative logo

EU Authorized Representative for Surgical Mask and Drape Manufacturers: Rule 1, Class I and the Sterile Route

Surgical masks, drapes and gowns intended for a medical purpose are class I under Rule 1 of Annex VIII to Regulation (EU) 2017/745. A non-sterile product needs no notified body; a sterile product is class I (Is) and Article 52(7)(a) limits the notified body to the sterility aspects. Whatever the variant, a manufacturer outside the EU must designate a sole authorized representative under Article 11(1) before the product reaches the Union market.

Which products this page covers and the qualification question

This page covers surgical face masks, surgical drapes, incision drapes, surgical gowns and clean-air suits that are placed on the market as medical devices. The first question for a mask is not its class but whether it is a medical device at all. The MDR definition turns on the manufacturer's intended purpose:

"‘medical device’ means any instrument, apparatus, appliance, software, implant, reagent, material or other article intended by the manufacturer to be used, alone or in combination, for human beings for one or more of the following specific medical purposes:"

Source: Regulation (EU) 2017/745, Article 2(1)

"diagnosis, prevention, monitoring, prediction, prognosis, treatment or alleviation of disease,"

Source: Regulation (EU) 2017/745, Article 2(1), first indent

A surgical mask whose stated purpose is to prevent the transmission of infective agents from the wearer to the patient, or a drape whose purpose is to maintain a sterile field around the surgical site, is intended for the prevention of disease in the patient and qualifies under that indent. A product whose only stated purpose is to protect the wearer is not described by this definition; its manufacturer should check the legislation that applies to protective equipment before asking about an authorized representative. Medex does not assess products outside the MDR.

Rule 1: class I, with the sterile question

Masks, drapes and gowns do not penetrate the body and are covered by the fall-back rule of Annex VIII:

"All non-invasive devices are classified as class I, unless one of the rules set out hereinafter applies."

Source: Regulation (EU) 2017/745, Annex VIII, Rule 1

MDCG 2021-24 lists incision drapes as a class I example under Rule 1. Where a drape is intended to contact injured skin, for example an incision drape applied over the surgical wound, Rule 4 gives the same result because the product is a mechanical barrier:

"class I if they are intended to be used as a mechanical barrier, for compression or for absorption of exudates;"

Source: Regulation (EU) 2017/745, Annex VIII, Rule 4, first indent

The variable that changes the conformity route is sterility. Article 52(7) keeps class I devices with the manufacturer's own declaration but brings in a notified body for the sterile condition:

"Manufacturers of class I devices, other than custom-made or investigational devices, shall declare the conformity of their products by issuing the EU declaration of conformity referred to in Article 19 after drawing up the technical documentation set out in Annexes II and III. If those devices are placed on the market in sterile condition, have a measuring function or are reusable surgical instruments, the manufacturer shall apply the procedures set out in Chapters I and III of Annex IX, or in Part A of Annex XI. However, the involvement of the notified body in those procedures shall be limited:"

Source: Regulation (EU) 2017/745, Article 52(7)

"(a) in the case of devices placed on the market in sterile condition, to the aspects relating to establishing, securing and maintaining sterile conditions;"

Source: Regulation (EU) 2017/745, Article 52(7)(a)

A non-sterile surgical mask is therefore plain class I: the manufacturer draws up the technical documentation of Annexes II and III, issues the EU declaration of conformity, registers in EUDAMED and applies the CE mark without any notified body. A sterile drape, a sterile gown or a sterile mask is class I (Is) and needs a notified body certificate limited to the sterilisation process.

Classification table

Product variantClassRuleNotified body
Surgical face mask, non-sterileIAnnex VIII, Rule 1None
Surgical face mask, sterileI (Is)Annex VIII, Rule 1; Article 52(7)(a)Limited to sterility
Surgical drape, non-sterileIAnnex VIII, Rule 1None
Surgical drape or incision drape, sterileI (Is)Annex VIII, Rules 1 and 4; Article 52(7)(a)Limited to sterility
Surgical gown or clean-air suit, sterileI (Is)Annex VIII, Rule 1; Article 52(7)(a)Limited to sterility
Mask intended only to protect the wearerNot a medical deviceArticle 2(1)Outside the MDR

What the class I route still requires

No notified body does not mean no obligations. The manufacturer needs technical documentation under Annexes II and III, a quality management system under Article 10(9), a Basic UDI-DI for each product, EUDAMED registration under Article 29, labelling that names the authorized representative, and post-market surveillance:

"For class I devices, including sterile, those with a measuring function and the reusable surgical instruments, the manufacturer must prepare and maintain a post-market surveillance report (MDR Article 85), which must be made available to the competent authorities on request."

Source: MDCG 2021-24, Guidance on classification of medical devices, Section 2.4

The authorized representative: Article 11

Whether a surgical mask, drape or gown manufacturer needs an EU authorized representative does not depend on the class of the product. It depends on where the manufacturer is established. Article 11(1) is the operative sentence:

"Where the manufacturer of a device is not established in a Member State, the device may only be placed on the Union market if the manufacturer designates a sole authorised representative."

Source: Regulation (EU) 2017/745, Article 11(1)

Article 11(2) requires the mandate to be accepted in writing and to cover at least all devices of the same generic device group. Article 11(3) then lists the minimum tasks. For class I masks and drapes there is no certificate to verify, so the representative's first check is the declaration of conformity and the technical documentation; for sterile products it also checks the sterility certificate.

"(a) verify that the EU declaration of conformity and technical documentation have been drawn up and, where applicable, that an appropriate conformity assessment procedure has been carried out by the manufacturer;"

Source: Regulation (EU) 2017/745, Article 11(3)(a)

"(b) keep available a copy of the technical documentation, the EU declaration of conformity and, if applicable, a copy of the relevant certificate, including any amendments and supplements, issued in accordance with Article 56, at the disposal of competent authorities for the period referred to in Article 10(8);"

Source: Regulation (EU) 2017/745, Article 11(3)(b)

"(g) immediately inform the manufacturer about complaints and reports from healthcare professionals, patients and users about suspected incidents related to a device for which they have been designated;"

Source: Regulation (EU) 2017/745, Article 11(3)(g)

One mandate for the European Union and Türkiye

Medex is established in Türkiye and registered in EUDAMED as an authorized representative under SRN TR-AR-000057550, so a surgical mask, drape or gown manufacturer outside both the EU and Türkiye covers both markets with one mandate. MDCG 2022-16, footnote 1:

"The ’Union market’ refers to the territories of the European Union Member States, and due to the European Economic Area (EEA) is extended to Norway, Lichtenstein and Iceland, and via the Customs Union Agreement to Turkey."

Source: MDCG 2022-16, Guidance on Authorised Representatives, footnote 1

The Commission's Notice to Stakeholders of March 2022 draws the conclusion:

"manufacturers established outside the territory of the EU or Turkey only need to designate one authorised representative, either in the EU or in Turkey, in order to place medical devices on the market in the EU or in Turkey."

Source: European Commission, Notice to Stakeholders: EU-Turkey Customs Union Agreement in the field of medical devices, Section I.2

Placing the product on the Turkish market also requires registration in ÜTS (Ürün Takip Sistemi), Türkiye's product tracking system, a separate service under a separate contract: see ÜTS registration for foreign manufacturers and surgical mask ÜTS registration in Türkiye (Turkish).

A separate Turkish page exists for surgical drape and gown ÜTS registration in Türkiye (Turkish).

What Medex does under the mandate

We verify that the EU declaration of conformity and technical documentation for each surgical mask, drape or gown device exist and that the notified body procedure has been carried out, keep copies for the period in Article 10(8), register in EUDAMED and check your Basic UDI-DI records, answer competent authority requests, cooperate on corrective actions and pass complaints and suspected incidents to you without delay. A person responsible for regulatory compliance is available in-house.

Class I products, sterile or not, fall in the band of €800 to 1,000 per year, fixed for three years from signature. Setup is €0 and a change of representative costs nothing; see pricing and EU authorized representative cost. We do not validate sterilisation processes and we do not test masks. We are not a notified body and we do not find importers or distributors. Offices in Ankara and İstanbul.

The symbol that identifies the representative on your label is explained in our guide to the EC REP meaning. If some devices are still placed on the market under the former directives, see the authorized representative for legacy devices.

Related pages

Other class I groups with their own pages include examination and surgical gloves, wound dressings and compression stockings. All groups are listed on the medical device categories page. For procedure packs see systems and procedure packs under Article 22. The general guide is EU authorized representative.

Frequently asked questions

Is a surgical mask a class I medical device?

Yes, when the manufacturer intends it for a medical purpose such as preventing transmission of infective agents to the patient. Rule 1 of Annex VIII places non-invasive devices in class I. If it is placed on the market sterile, Article 52(7)(a) brings in a notified body for the sterility aspects only.

Do non-sterile surgical masks need a notified body?

No. Article 52(7) lets the manufacturer of a class I device issue the EU declaration of conformity after drawing up the technical documentation. The notified body is involved only for devices placed on the market in sterile condition, with a measuring function or as reusable surgical instruments.

Are sterile drapes and gowns class I (Is)?

Yes. They remain class I under Rule 1, and Rule 4 gives the same class for drapes used as a mechanical barrier on injured skin. The sterile condition triggers Article 52(7)(a): a notified body certificate limited to establishing, securing and maintaining sterile conditions.

Does a non-EU mask manufacturer need an authorized representative even for class I?

Yes. Article 11(1) applies to every manufacturer not established in a Member State, regardless of class. For class I the mandate is the only EU-side appointment the Regulation requires.

Does the Medex mandate also cover the Turkish market?

Yes. The Commission Notice of March 2022 states that manufacturers outside the EU or Turkey need only one authorized representative, in the EU or in Turkey. Registration in ÜTS is a separate service.

Sources and further reading

Regulation (EU) 2017/745 on medical devices, consolidated text: eur-lex.europa.eu/legal-content/EN/TXT/?uri=CELEX:02017R0745-20250110

MDCG 2021-24, Guidance on classification of medical devices: health.ec.europa.eu/medical-devices-sector/new-regulations/guidance-mdcg-endorsed-documents-and-other-guidance_en

MDCG 2022-16, Guidance on Authorised Representatives Regulation (EU) 2017/745 and Regulation (EU) 2017/746: health.ec.europa.eu/medical-devices-sector/new-regulations/guidance-mdcg-endorsed-documents-and-other-guidance_en

European Commission, Notice to Stakeholders: EU-Turkey Customs Union Agreement in the field of medical devices (March 2022): health.ec.europa.eu/system/files/2022-04/md_eu-turkey_customs-union_en.pdf

Request a fixed-price EU authorized representative quote for your surgical masks, drapes or gowns.

Request a proposal  ·  View pricing  ·  Appoint Medex as your authorized representative

bottom of page